However, if the problem was interference on the usb line, then I should get the same buzzing sound when I connect the RGC to the tv and XBox via component cable as well. The USB A to B runs through the wall to a computer in another room, and is 25 feet long. The RGC, XBOX, Television and A/V receiver are all sitting on the same entertainment center, and connected with standard 3ft hdmi cables. The only cable that is of any unusual length is the USB A to B that powers the unit. But since it is an electronic device, hooked (as directed by the manufacturer) to other electronic devices, it is obviously not functioning properly. One imagines it would not make that noise if it were, for example, connected to the toilet in my bathroom. It is connected to the XBox in the room the XBox is in. It's not "only defective in one room of my house". If I buy a different device, from a different company, and get the same result.then the problem is on my end and I will have to either give up on recording my gameplay, or make some kind of major change to the way things are set up. It is possible I simply got a defective unit. But since this decice is designed with the purpose of being connected to a gaming system, a television and a computer simultaneously, one would assume that the manufacturer would assume there might be some electricity around it, and design accordingly. I also understand that the sound I am hearing is likely electrical interference. I spent the better part of 5 years doing cabling and infrastructure. I have owned this XBox and this television and this A/V receiver, all working fine, for more than 5 years. I am not interested in getting a degree in electronics and/or rewiring my house in order to make this device do what it is supposed to do.īy the way, just for informational purposes, I am not an initiate when it comes to these types of things. I just want to plug in a device and record myself playing games, specifically Rocksmith 2014 right now. My best guess is that there is some problem with the RGC's HDMI port, as I do not hear this sound on my television or my A/V unit unless this device is plugged in. Having spent $119 +shipping, and then spending an additional $100+ on "quality" cables in an attempt to eliminate what I assume is electrical interference, I am done. Whether they grant me one or not, I am going to buy a different device from a different manufacturer. I have grown weary of messing with this device, and I have requested a refund. You will also note if you look carefully as the notes pass, that the video and audio are out of synch ever so slightly. If you would like to hear the sound of which I speak it can be heard in the following video which I recorded. I have literally spent the better part of 4 days on my stomach in the floor hooking up cables and unhooking them, trying to find a solution to this problem. However, the colors displayed on the television set are messed up, with everything having a green tint to it. When I switch from HDMI to component cabling the buzz goes away. I have tried every possible combination of cabling solutions. The USB connection from the computer in the office goes through the wall seperating the office from the living room and in to the RGC. Sound from my XBox 360 goes directly to my A/V receiver via optical cable. It is connected to my Mitsubishi DLP television via HDMI. It is very strange and frustrating and I am not sure why it does it.As I said, the RGC is connected to my XBox 360 via HDMI. When I change it back it does this refresh looking thing and goes back to the HDMI setting. Every time it does this it goes from what I had set "component" to "HDMI". Now once I turn the console on the program does something that looks like it is refreshing, like when you refresh a page on the internet. Now, previously that was fine at it would go from "no Signal" to "ready" and that was me ready to record but not anymore for some reason. Once that has loaded up fully I then turn on the console which is a PS3. I then open up the Capture section of the program and set he input method to Component as that is what the tutorial said to do and that is also what I had been using when recording previously. I set up the equipment and plug the USB in to the laptop and open up the capture program. I set everything up exactly like it mentions in the tutorial. I have had about 2 weeks where it was working perfectly but recently it has not been working at all. I have been having issues lately with the HD Pro software on my laptop when I set it up for recording.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |